1.当环氧地坪漆在正常使用情况下，有先用经济型普通环氧地坪或者耐压砂浆环氧地坪漆厚度为0.5毫米-3.0毫米,能使用约三至五或者10以上年,随着厚度增加,使用年限也不断增加.

1. When the epoxy floor paint is used normally, the thickness of the epoxy floor paint is 0.5 mm-3.0 mm, which can be used for about three to five or more years, and the service life increases with the thickness.

2.有些工厂由于承压这方面的需求，经常有载重叉车自重加上载重有五吨至十吨左右，所以需要在产品设计时增加厚度，加环氧环氧地坪漆里面加上石英砂或者金刚砂骨料有助于增加抗压性及耐冲击性，有效地达到产品使用要求；

2. Some factories often have forklift trucks with loads ranging from 5 to 10 tons due to the pressure requirement, so it is necessary to increase the thickness of the product design. Adding quartz sand or diamond aggregate to the epoxy floor paint will help to increase the compression resistance and impact resistance, and effectively meet the product requirements.

3.在抗腐蚀方面，如机械厂的油污，化工厂的溶剂都需要产品达到防腐蚀要求，这就需要用不同的固化剂来提高产品的性能，固化剂分防腐蚀性的，耐温的，低温固化等各种类型，要求防腐要求较客的情况下则要选用环氧改性的乙烯基酯环氧地坪材料来达到特殊要求。

3. In the aspect of corrosion resistance, such as oil pollution in machinery factory and solvent in chemical plant, all the products are required to meet the anticorrosion requirements, which requires different curing agents to improve the performance of the products. The curing agents can be classified into anticorrosive, heat-resistant, low-temperature curing and so on. When anticorrosive requirements are relatively good, epoxy modified ones should be selected. Vinyl ester floor materials meet special requirements.

为了帮助使用环氧地坪装饰保护涂料的顾客正确地选择地坪的种类和有效控制建设成本，建议顾客最好从以下几个因素入手：

In order to help the customers who use floor decorative protective coatings choose the types of floor correctly and control the construction cost effectively, it is suggested that the customers should start with the following factors:

一：机械性能要求主要以下三个方面：

1: mechanical performance requirements are mainly in three aspects:

1. 耐磨性：耐磨地坪在使用时会有哪些车辆行走；

1. wear resistance: what vehicles will be used when the wearable floor is used?

2. 耐压性：地坪在使用时会承受多大荷载；

2. pressure resistance: when the floor is used, it will bear much load.

3. 耐冲击性：冲击力是否会引起地坪面剥离；

3. impact resistance: will impact force cause floor surface peeling?

二：化学性能要求

Two: chemical performance requirements

主要考虑以下两个方面：

The following two aspects are mainly considered:

1. 耐酸碱性：使用时腐蚀性化学物质的种类及浓度。

1. acid and alkaline: the type and concentration of corrosive chemicals used.

2. 耐溶剂性：使用时溶剂类型及接触时间。

2. solvent resistance: solvent type and contact time.

三：楼层位置状况

Three: floor location status

根据地坪是在地下楼层还是地面楼层的位置，确定是否需要防潮处理或选择特殊防潮地坪？

According to the location of the floor in the basement floor or the ground floor, whether the need for moisture-proof treatment or select a special moisture-proof floor?

四：基面状况

Four: base level condition

1. 基层强度：一般要求抗压强度≥20Mpa

1. base strength: General requirements, compressive strength is greater than or equal to 20Mpa

2. 平整度：是否需要用环氧砂浆修补？

2. Flatness: is it necessary to repair with epoxy mortar?

3.地面施工前一般需要用自流平处理

3. self leveling is usually required before surface construction.

五：美观要求

Five: aesthetic requirements

1. 颜色要求：是否需要颜色划分区域？

1. color requirements: do you need a color division area?

2. 亮度要求：是选择亚光还是亮光？

2. brightness requirement: choose matte or bright light?

3. 平整度要求：是否对地坪的平整度有要求？

3. flatness requirement: is there any requirement for the smoothness of the floor?

六：安全性要求

Six: Safety requirements

如果地坪处在油渍环境或坡道处，则需要选择防滑地坪；如果在加油站，油库等特殊场所需要选择防静电、防爆的。

If the floor is in an oil-stained environment or ramp, you need to choose anti-skid floor; if the gas station, oil depot and other special places need to choose anti-static, explosion-proof.

七：施工工艺

Seven: Construction Technology

1、基面处理；

1, base surface processing;

2、涂刷封闭底漆；

2. Brush the primer.

3、批刮腻子；

3, batch scraping putty;

4、打磨、吸尘；

4, grinding and vacuuming;

5、涂刷色漆；

5, brush the paint.

底漆采用环氧树脂底漆主剂：固化剂，调制均匀固化10分钟左右，用羊毛滚筒滚涂一遍，底漆主要是封闭基础层，封闭水气及灰尘

The primer adopts epoxy resin primer main agent: curing agent, curing uniformly for about 10 minutes, with wool roller roll coating, primer is mainly to seal the base layer, sealing moisture and dust

6.填补处理

6. fill in

用环氧漆石英砂调制环氧砂浆，填补伸缩缝及破损处

Epoxy mortar is modulated with epoxy sand and quartz sand to fill the expansion joint and damage place.

7.批刮中层

The 7. batch scraping middle layer

8.上环氧树脂面漆

8. epoxy top coat

9工程养护

9 engineering maintenance

八：技术指标

Eight: technical indicators

干燥时间 表干 ≤4

Drying schedule is less than 4.

实干 ≤24

Actual work is less than 24

附着力（级） ≤1

Adhesion force (grade) is less than 1

铅笔硬度 ≥2H

Pencil hardness is more than 2H

耐冲击性 50通过

Impact resistance 50 passes

柔韧性 1㎜通过

Flexibility 1 pass

耐磨性（750g/500R，失重g）≤0.03

Wear resistance (750g/500R, weightlessness g) is less than 0.03.

耐水性 48小时无变化

No change in water resistance for 48 hours.

耐30%硫酸 7天无变化

Resistant to 30% sulfuric acid for 7 days without change.

耐40%氢氧化钠 7天无变化

40% NaOH resistant for 7 days without change.

耐汽油 120# 7天无变化

Gasoline resistant 120# remained unchanged for 7 days.

耐润滑油 7天无变化

No change in lubricating oil for 7 days.

九：性用性能要求

Nine: sexual performance requirements

1.洁净度要求：对于洁净度要求高的场所，宜采用自流平地坪，洁净度要求越高，自流平面层设计越高。

1. Cleanliness requirements: For places with high cleanliness requirements, self-leveling floor should be used. The higher the cleanliness requirements, the higher the design of self-leveling floor.